About Us
Listing Photo

At Paint & Coatings Contractors we have been certified professional painters since 2004 performing residential and commercial painting. Since then we have strictly focused on painting and coatings, expanding our knowledge of innovative materials and application techniques. Over the years, we have been proven to save our clients money by only working with specialty tradesmen, who perform with optimum efficiency while also providing a superior quality of work.

We are currently approved to work in Broward and Dade Counties.

We have created associations with HOA's to provide reliable painting service as part of mandated maintenance. Click here to view one of the boards where we assist regularly.

In our company's history many high profile projects have been completed included high-rise beach-front hotels, commercial warehouses with steel outfitting, chain restaurants such as Lime Fresh, retail stores including Victoria's Secret, Aeropostale, Carter Kids Clothing, Shops at Bal Harbour and many more.

The management team at Paint & Coatings Contractors works directly with our clients and painters. This allows us to generate a great understanding between our clients' desires and the work performed.

Want to attempt a DIY Painting Project? Here are some tips to help you paint like a Paint & Coatings Contractors, Inc. Pro!

A poorly executed paint job is easy to spot, with its drips and slips and uneven lines. More often than not, haste is the culprit. But with some thorough preparation up front, many of the possible pitfalls will be eliminated—and the actual painting will be much easier, as well. So before you crack your first paint can, schedule in a full day for prep.

The best prep starts with sanding and sometimes requires scraping. Sanding scuffs up the existing surface so the paint grabs hold; scraping will take off any old bumps or drips. (Be aware of how many layers down there may be lead paint, last sold in the early 1980s; sanding isn’t likely to reveal it, but scraping might.) You should also take your time patching holes, caulking gaps, and cleaning dust or grease with soap and water so you start with a pristine surface.

If you’re working with new walls, or if you’ve patched any holes before you start, you’ll also need to prime. Paint & Coatings Contractors always use primer to fill in spongelike pores and creates an even, solid base that takes paint well. You should also prime if you’re going from a dark to a light color or vice versa. (In the latter case, have the paint store tint the primer to go with your wall color. It will save you at least one coat of paint later on.)

First-time painters tend to tape every edge to guard against misstrokes. But that can bring on its own problems if paint bleeds under the tape or if you peel paint off when removing it. It’s more efficient to use angled brushes, which draw a straight line when turned on edge. Proper use of an angled brush can save you hours of setup and touch-up.

Angled brushes also come in handy for cutting in along corners and ceilings and around trim, where rollers can mark. Fill in a few inches at these spots, then marry the line with the field by rolling over them. Keep a wet edge to avoid dark spots or paint pulls.

As you paint, be sure to keep moving: Put the paint on the wall, level it out where it’s heavy, and get on with it. Don’t use back-and-forth brushstrokes, and don’t spend time making the first coat look perfect (it won’t be). Finally, take a tip from Paint & Coatings Contractors, Inc. and always keep a damp rag in your pocket to quickly wipe up your mistakes. Even the best painters color outside the lines once in a while.

After removing any wall art and moving furniture away from the walls, lay canvas tarps (more absorbent and less slippery than plastic) over the furniture and on the floor. Using painter's tape, fasten down the edges. Unscrew all switch plates and electrical outlet covers, and tape over the remaining switches and holes with painter's tape. Tape around any other hardware that can't be removed.

Always sand and paint the ceiling completely (following these same steps) before addressing the walls.

Using a pole sander fitted with 120-grit paper, sand the walls (make sure to wear a dust mask). Sweep the sander side to side as you work your way from the top down. Apply medium pressure, and take care that the head doesn’t flop and gouge the wall. Change the paper whenever the grit gets clogged with dust.

Remove bumps or drips on painted molding with a scraper. Then, using a dampened coarse-grit sanding sponge, rough up the surface. Keep a bucket of warm water nearby, and continually rinse the sponge. Finish with a dampened fine-grit sponge.

Using a wet/dry vacuum, clear all the dust from the walls and trim. If necessary, wash the walls with a sponge, using warm water and dish soap. Scrub greasy or waxy spots. Wipe everything down one last time with clean water, if needed.

Run a thin bead of caulk over any gaps where molding meets wall. Wet your finger and smooth the caulk with even pressure to push it into the crack and leave a crisp edge.

Using a putty knife, fill any small divots or holes in the walls. Use patching compound for plaster and joint compound for drywall. Sand the filler smooth with 120-grit sandpaper.

Prime the patched spots (or the whole wall if necessary). Sand primed areas with 120-grit sandpaper, and wipe clean of dust with a damp sponge.

Dip a 2½-inch angled brush into a bucket of paint, loading the paint only a third of the way up the bristles. Tap off—don't wipe—the excess on the side of the bucket. Use the brush to cut in a 2 to 3-inch band of paint at all corners, against the ceiling, and next to molding; this will give the roller some breathing room so it doesn't bump against adjacent areas.

To cut in, run a line of paint along the wall about an inch away from the edge. Then turn the brush onto the bristle tips, and press down slightly so the longest bristles gather into a point. Use this point to draw a careful line of paint right up to the edge where wall meets trim. Once you have a clean line in place, level out any heavy areas or drips, then move on. In order to keep a wet edge, don't work in too large an area at one time.

Once you've cut in around an entire wall area, use a roller to fill in the field. Dampen the roller before using it (with water for latex paint or paint thinner for oils). Dip the roller in a tray filled with just enough paint to reach the grate. Roll it back against the grate to distribute the paint and squeeze out the excess. Make sure the roller is covered completely before painting with it.

Roll a W or M shape on the wall to distribute the bulk of the paint. Then use overlapping vertical strokes to spread paint evenly between the lines. Continue painting the wall in this manner until it is covered. Overla

Years in Business

Paint & Coatings Contractors Inc. has been in business for 7 years.

Special Offer

Free, no-obligation Estimates

CALL NOW
Local: 954-699-0155

Request Phone Call

Testimonials
I scheduled an appointment effortlessly from California on a Wednesday. I arrived Thursday morning in Pembroke Pines and met the estimator. The painting began that night and the entire home was painted perfectly by Sunday. The work was not only done exactly how I wanted it, but it was done quickly with minimal input on my behalf. I am more than happy with the quality of their work and I look forward to using them in the future for any project. Thanks!
Shawn A.